This page is a working reference for those who want to plan out their optic and sight options with our slides. Most of these optic cuts are available through our special order pages. The chart below summarizes most of the options we offer while addressing the following technical specifications:
- What optic cut to use for a specific optic (Section A)
- What the optic mount holes are tapped for (Section B)
- Which sight options provide a lower 1/3rd co-witness or other notable setups (Section C)
- Any notable information i.e. installation pitfalls, suggestions, special notes (Section D)
As always, feel free to reach out to info@norsso.com for any questions.
| Optic/Sight setup info - Glock Standard Width (G17, G19, G26, .40S&W Gen 3-4 equivalent) [Updated 7/18/24] | |||||||
| Section A - Optic cut selection | Section B - Optic Mounting | Section C - Sight Selector (x = lower 1/3rd cowitness) [Front Height-Rear Height] | Section D - Misc | ||||
| Optic | Norsso Optic Cut Option | Slide thread pitch | Suggested hardware | Night Fision [163-175] | Amgeriglo GL-429 [315-314] | Night Fision [290-313] | Setup Notes |
| Aimpoint Acro | Aimpoint Acro | Custom Rail | No hardware needed | x | x | ||
| Delta point Pro w/ Rear sight attachment | Delta point Pro (no rear dovetail) | M4 | Manufacturer's Set (M4) | Need special sight (.407" tall front) | Ameriglo GST 407 works | ||
| Holosun 407C/507C/508T | Holosun 407C/507C/508T | 6-32 UNC | Manufacturer's set (shorter length) | x | x | ||
| Holosun 507K | Holosun 507K/EPS Carry*/RMSc Shield) | M4 | Manufacturer's set (M4, largest diameter, max 12mm length) | x | x | ||
| Holosun SCS MOS | Holosun SCS MOS | M3 | Norsso provided screws | x | Absolute Cowitness for these sights | ||
| Holosun SCS 320 | Holosun SCS 320 | M4 | Manufacturer's set | x | x | ||
| Holosun EPS Carry | Holosun 507K/EPS Carry*/RMSc Shield) | M4 | Manufacturer's set (M4, largest diameter, max 12mm length) | Slightly taller than 1/3rd cowitness | |||
| Holosun EPS (Full size) | Holosun 507K/EPS Carry*/RMSc Shield) | M4 | M4 x 10mm long set from calc kinetics (Link here) | x | x | ||
| Holosun 509T | Holosun 509T or Reverse 509T | Custom Rail | No hardware needed | x | x | ||
| Steiner MPS | Aimpoint Acro | Custom Rail | No hardware needed | x | x | Small gap in front of optic (about 1/8") | |
| Trijicon SRO | Trijicon RMR | 6-32 UNC | Norsso provided screws | Need minimum of 330-353 height sights for lower 1/3rd | Recommend suppressor height for lower 1/3rd | ||
| Trijicon RCR | Trijicon RMR | 6-32 UNC | Manufacturer's Set (short capstan screw set) | TBD | Still testing | ||
| Trijicon RMR | Trijicon RMR or Reverse RMR | 6-32 UNC | Norsso provided screws | x | x | ||
| Trijicon RMRcc (Concealed Carry optic) | Trijicon RMRcc | 6-32 UNC | Manufacturer's Set | x | x | Unique footprint, no other optic works with this cut yet | |
| Trijicon RMR HD | Trijicon RMR HD | 6-32 UNC | Manufacturer's Set (short set) | x | x | ||
| Vortex Venom | Vortex Venom | 6-32 UNC | Norsso provided screws, must install after internal parts | Need minimum of 330-353 height sights for lower 1/3rd | Recommend suppressor height for lower 1/3rd | ||
| Vortex Viper | Vortex Viper | 6-32 UNC | Norsso provided screws | x | x | ||